关于电阻炉的那些事儿

今天小编给大家介绍电阻炉的相关事宜，有兴趣的话可以关注我们哦！

电阻炉的安装操作：开车前检验轨道有无障碍物，钢丝绳、卷扬机、托轮、小托车需要保证完好，并按规定加油润滑；而且开车人员必须听从装炉操作人员指挥，密切配合。

电阻炉炉芯位置确定要准确，反应箱垂直吊放，高度适中，放置端正，两排箱体之间保持等距，确保尺寸的准确。严禁炉车在运行中吊反应箱，放反应箱时，按顺序摆放。每放完一部炉料后，电阻炉的料斗闭合器要关严密。炉料装完后，洒在端墙拉杆上的乏料或石墨要清理清理干净，卷扬机小车停放在安全位置，压起顶轴，用盖盖好，并将所装炉号及装炉异常情况填入工艺卡片，随炉传送托车组。

电阻炉的扒炉操作：冶炼炉停炉24小时之后，才能进行扒炉操作。可以根据当天风向确定扒墙顺序，如果吊环断裂脱落或无吊环，上炉挂钩的人员需要高度集中注意力，做好安全措施，在炉墙上小心稳步行走，挂好钩后立即返回安全位置，指挥起吊。大墙如无吊环，应先吊炉墙，后吊支柱。切、扒乏料、黄块时，指挥人员需站在安全位置。

电阻炉的铲炉操作：冶炼炉停电一定时间后，应将残余黄块、乏料清理干净，用水清理炉台乏料时，不要出现里高外低斜坡形或高低不平的情况，要与小墙上端水平。

在清理电阻炉的时候，结晶筒上不允许跨越，更不可站在上面。操作时密切注意结晶筒有无倒塌迹象，在炉台上行走时要小心谨慎，以防失足跌入水池，发现小墙倾斜严重时，应及时进行调整。

                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                停放在安全位置，压起顶轴，用盖盖好，并将所装炉号及装炉异常情况填入工艺卡片，随炉传送托车组。

电阻炉的扒炉操作：冶炼炉停炉24小时之后，才能进行扒炉操作。可以根据当天风向确定扒墙顺序，如果吊环断裂脱落或无吊环，上炉挂钩的人员需要高度集中注意力，做好安全措施，在炉墙上小心稳步行走，挂好钩后立即返回安全位置，指挥起吊。大墙如无吊环，应先吊炉墙，后吊支柱。切、扒乏料、黄块时，指挥人员需站在安全位置。

电阻炉的铲炉操作：冶炼炉停电一定时间后，应将残余黄块、乏料清理干净，用水清理炉台乏料时，不要出现里高外低斜坡形或高低不平的情况，要与小墙上端水平。

在清理电阻炉的时候，结晶筒上不允许跨越，更不可站在上面。操作时密切注意结晶筒有无倒塌迹象，在炉台上行走时要小心谨慎，以防失足跌入水池，发现小墙倾斜严重时，应及时进行调整。

                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                   停放在安全位置，压起顶轴，用盖盖好，并将所装炉号及装炉异常情况填入工艺卡片，随炉传送托车组。

电阻炉的扒炉操作：冶炼炉停炉24小时之后，才能进行扒炉操作。可以根据当天风向确定扒墙顺序，如果吊环断裂脱落或无吊环，上炉挂钩的人员需要高度集中注意力，做好安全措施，在炉墙上小心稳步行走，挂好钩后立即返回安全位置，指挥起吊。大墙如无吊环，应先吊炉墙，后吊支柱。切、扒乏料、黄块时，指挥人员需站在安全位置。

电阻炉的铲炉操作：冶炼炉停电一定时间后，应将残余黄块、乏料清理干净，用水清理炉台乏料时，不要出现里高外低斜坡形或高低不平的情况，要与小墙上端水平。

在清理电阻炉的时候，结晶筒上不允许跨越，更不可站在上面。操作时密切注意结晶筒有无倒塌迹象，在炉台上行走时要小心谨慎，以防失足跌入水池，发现小墙倾斜严重时，应及时进行调整。